- IC 756 PRO II NO TX POWER HOW TO
- IC 756 PRO II NO TX POWER SERIAL
- IC 756 PRO II NO TX POWER MANUAL
- IC 756 PRO II NO TX POWER SOFTWARE
- IC 756 PRO II NO TX POWER WINDOWS
IC 756 PRO II NO TX POWER SOFTWARE
Verify that the PLAYBACK software volume controls for the SignaLink USB are set according to the "Output Attenuator" feature, then this should be set to You are using an older version of HRD/DM-780 with the
Level control (WSJT-X, etc.), then this will need to be turned up. If your communication program has a built-in transmit The program should have “USB Audio CODEC” selected as the sound card for Verify that your communication program is configured to use the SignaLink USB’s built-in sound card. Have a problem with your SignaLink and you should contact Tech Support by If none of these make any difference, then you may Still won't turn ON, then try changing USB cables, USB ports, or using aĭifferent computer. Is securely connected to the computer and the SignaLink. Make sure that the SignaLink USB's PWR switch is pressed in and the USB cable Verify that the SignaLink USB’s PWR LED is ON. Won't transmit (SignaLink USB's Red PTT indicator is OFF).
IC 756 PRO II NO TX POWER MANUAL
Please refer to the SignaLink Manual for details.
IC 756 PRO II NO TX POWER HOW TO
If you are not sure how to adjust the software volume controls, then Be sure that your volumeĬontrol panel shows "USB Audio Codec" or you will be adjusting the volume for the wrong
IC 756 PRO II NO TX POWER WINDOWS
The "Application" control should be at 50% (note that in Windows XP, Installation Manual and on our web site, the "Speaker" control should be at 100% (max) and Set, so they can look correct at a glance. Things can cause this to happen as well, so please check your Windows Sound card in Windows, or accidentally mute the SignaLink's output. This can happen if you unplug the USB cable, change the default This is the most common problem we hear about and it is virtually **always** due to the software volume controls being reset by SignaLink USB was working perfectly but now will no longer Transmit. Rate offset error on some Windows ME, 2000 and XP systems
Time I open the Window's Volume Control Panel, it has reset back to my SignaLink USB's software volume controls to incorrect positions Using the SignaLink USB - Is this correct?ĭon't see a "New Hardware Found" (or similar) message when I firstĩ8 can't find a file during installation. See "USB Audio Device", but not "USB Audio Codec" when General settings must I make when configuring my communications program?
IC 756 PRO II NO TX POWER SERIAL
I select a serial port when configuring my communications program? System Sounds cause the SignaLink USB to transmit.Ĭycles between Transmit and Receive when the 13-pin radio cable is pluggedĭo I operate "direct keyed" CW with the SignaLink? SignaLink USB's TX control is "touchy", making if difficult toīack to me when I answer their CQ, or they tell me that I'm off frequency Transmits, but there is no power output or it is too low. Won't transmit (SignaLink USB's PTT indicator is ON). Won't transmit (SignaLink USB's PTT indicator is OFF). SignaLink USB was working perfectly but now will no longer Transmit (PTT LED Listed here, then please contact our Technical Support Staff If you are unable to resolve your problem, or if you do not find your problem Here if you are experiencing a "Sound Card Error" after a Windows 10Īre the most common problems reported to our Technical Support Staff. Problem without having to call Tech Support. Look through ALL of the information below and you should be able to resolve the Resolved by carefully following the tips below. Software volume controls, sound card communication program, or radio, and can be Your SignaLink USB is most likely due to incorrect setup of the SignaLink, Unless you have experienced a nearby lightening strike, power supplyįailure, or some other catastrophic event, whatever issue you are having with SignaLink has proven itself to be very reliable since its release several yearsĪgo. Some time without any trouble but now find that it has stopped working.Įvery SignaLink and radio cable is 100% tested before shipping, and the This is true forīoth new installations, and for those that have been using their SignaLink for The SignaLink USB are due to simple configuration issues. Virtually all of the Technical Support calls that we receive for Troubleshooting or calling for assistance! NOTE: For non-technical questions, please see our SignaLink USB Troubleshooting SignaLink USB Troubleshooting,